The Lost Mary BM6000 is a popular vape that many people enjoy. The vape provides users with 6000 puffs, a 650mAh battery capacity, and comes with a 2ml prefilled pod along with a 10ml refill container.
The QUAQ mesh coil provides users with amazing vapour and flavour, as well as having a power display screen and a transparent tank that allows you to keep track of your battery and e-liquid level.
Sometimes, it may not work as expected which can be annoying, especially while you are using it. This guide will help you figure out why your Lost Mary BM6000 is not working and show you how to fix common problems.
Vape Refuses to Power On and Function
This is another most common problems with the Lost Mary BM6000 Box Of 5. You try to puff, but the vape refuses to function or even power on. Possible reasons for this could include:
Dead battery
The BM6000 uses a 650mAh battery and over time, the battery may become fully drained. The vape should be charged using a Type C charger for a while. Also, there may be a problem with the charger or wall adapter if the screen isn't working.
Pod is not installed correctly
The vape won't work if the pod is loose. It needs to fit perfectly in order to make contact with the battery. Take out the pod and insert it again, and listen to whether it clicks when installing it. Use a cloth to clean the connections from dust and e-liquid residues.
Empty pod
The BM6000 has a 10ml e-liquid reservoir and a 2ml pod. If both are empty, the vape will not produce vapour. Check the transparent e-liquid tank to see if there is any left. If it is empty, you need to replace the pod or refill the container.
Weak or No Vapour Production
Another common issue is weak vapour. You take a puff but the vapour is thin or barely there. This can happen for several reasons.
The battery is low
When the battery gets low, the vape may not have enough power to heat the coil properly. This leads to weak vapour so check the power display screen. If the battery level is below 30%, charge the vape fully before using it again.
The coil is flooded
It often occurs that an excessive amount of e-liquid goes inside the coil, which means it gets flooded. Flooding takes place when you let your vape sit for a while or take very strong pulls when vaping. Remove the pod from the mouthpiece, then breathe into the pod. Wipe the bottom part of the pod using a tissue.
The coil burns out
QUAQ Mesh Coil is built to work for a long time but not forever. In case of a burnt smell or very faint vapour, it is possible that the coil gets burned out. It becomes necessary to replace the pod with a new one. For the BM6000, it is necessary to use only Lost Mary BM6000 Refill Pods.
Airflow is blocked
The vape needs airflow to work properly. Check the air holes on the side or bottom of the vape. If they are blocked by dirt or pocket lint, clean them out. Also, do not cover the airflow holes with your fingers while vaping.
The Vape is Leaking
Leaking is among the messiest problems faced by most vapers. The e-liquid can leak around the pod or even through the airflow holes. This can be caused by a few things.
The pod is not sealed properly
Make sure the pod is pushed all the way down until it clicks. If it is loose, e-liquid can escape. Also, check if the rubber seal on the pod is damaged and if it is, you need a new pod.
Too much e-liquid in the pod
The BM6000 has a 2ml prefilled pod and a 10ml refill container, so if you overfill the pod, it will leak. Only fill it up to the line marked on the side. Do not overfill.
The vape is stored incorrectly
If you leave the vape on its side or upside down for a long time, E-Liquid can leak out. Store it upright when you are not using it to prevent leaks and in order to keep the coil saturated properly.
The Vape Has a Burnt Taste
A burnt taste indicates that there is a problem with the coil/pod of your vape. This could make your vaping experience terrible to the point of throwing away your vape. Here is what to do.
The coil is dry
A coil without e-liquid will burn the cotton and provide you with a terrible taste when the coil is not saturated with enough liquid. See how much liquid is left in your pod and if it is less than half, then refill or change your pod. Give some time to your pod so that the new liquid can soak into the coil.
You are chain vaping
When you puff too fast, you do not allow the coil to re-soak in the e-liquid. As a result, you get a dry hit and taste something like burnt. Try to wait a few seconds between puffs.
The pod is old
Pods do not last forever. If you have been using the same pod for weeks, it is probably time for a new one. Replace the pod when the flavour starts to fade or taste off.
The Display Screen Does Not Work
The BM6000 features a power display screen which shows your battery level and your usage. If your screen is not displaying anything or glitchy then it can be quite irritating.
The vape is in sleep mode
Some vapes put themselves in sleep mode in order to preserve their battery level; therefore, take a puff on your vape or push the fire button to activate it. If your vape is still sleeping after trying these options, then it is probably drained of charge.
Software issue
The screen will freeze or display incorrect information sometimes. It's very uncommon, but it does occur. You may resolve this issue by simply charging your vape for a few seconds.
Conclusion
The Lost Mary BM6000 Wholesale is a quality vape, but like all other vapes, it can experience some technical difficulties. Most faults can easily be sorted out by yourself. Check the battery, clean connections and ensure the pod is attached.
Weak vapour production or burned flavour can be caused by a coil malfunction. Leaking may occur because of overfilling or improper storage, so you should store it upright and clean. A screen display problem may require just resetting the screen; if none of these help, then you need to buy another one.
This is quite normal for any vape, and most issues can be solved in just a couple of minutes. You should not throw the vape away without giving these tips a try.