How to Fill Your Vaporesso Pod: A Simple Refill Guide

Correctly knowing how to refill your Vaporesso pod is the most fundamental thing that one must learn. Make a mistake in refilling and get ready for leakage, burnt taste, or having to clean up the mess. 

Learning how to refill your Vaporesso pod correctly helps prevent leaks, burnt hits, and wasted e-liquid. Although the process is simple, small mistakes can affect performance and shorten the life of your pod. This guide explains each step so you can refill your pod confidently and avoid common problems. 

However, no need for panic as the process is not complicated at all once you understand how. This guide will show you exactly how to fill your Vaporesso pod. We'll cover everything from the prep work to fixing common problems.

Understanding Your Vaporesso Pods Type

It's important to know which type of pod you have before you start filling. Vaporesso uses two main designs across their vapes.

The most common is the top-fill system found on the XROS series. This is because the pods have a mouthpiece that just snaps right off to give access to the filling point. The pod does not even have to be detached from the battery.

The other type is the side-fill or bottom-fill system. Some Vaporesso pods, including certain Luxe models, use a side-fill design. These pods have a small silicone plug that you pull open. You must remove the pod from the battery before you can fill it.

Indeed, identifying your pod type is your first step. Trying to snap the top off a side-fill pod will break it. Likewise, trying to pull a silicone plug from a top-fill pod will damage the seal.

Before You Fill Your Vaporesso Pod

Before filling, check the pod for cracks, damaged seals, or excessive wear. A damaged pod is more likely to leak, even when filled correctly. Getting ready properly makes the whole process easier. Here's what you'll need:

• Your Vaporesso vape with an empty or nearly empty pod
• A bottle of your preferred e-liquid
• A tissue or cloth for any small spills
• A flat and clean surface on which to work

In addition, ensure that the type of liquid you are using is compatible with the pod. Using an inappropriate type of e-liquid will lead to leakage or burnt hits.

Refilling Your Vaporesso Pod: Step by Step

Refilling your pod is easy when you follow these instructions.

Step 1: Turn Off and Remove the Pod

First, turn your vape off. If your Vaporesso device has a power button, turn it off before refilling. Draw-activated models without a power button can simply be left unused while you refill the pod. This stops the vape from firing accidentally while you're filling.

If you have a top-fill XROS pod, you can leave it in the battery. If you have a side-fill pod, gently pull it out of the battery.

Step 2: Open the Fill Port

For top-fill XROS pods: Hold the pod firmly and push the mouthpiece off with your thumb. It should pop off easily and you'll see two holes. One is a central metal hole – this is for airflow. The other is the fill port, depending on the pod model, the fill port may be marked with a coloured silicone membrane. Only put liquid in the red fill port.

For side-filled pods: Find a tiny silicone plug on the side of the pod. Lift it up using your nail to see the filling hole.

Step 3: Take Your Time When Filling

Take your e-liquid bottle and put the nozzle inside the fill port. Apply gentle pressure on the bottle to fill the pod.

Here are some tips for you:

1. Don't overfill and stop before the liquid reaches the very top. Leave a small air gap – about 90% full is perfect. This air gap creates a vacuum that stops leaks.

2. Don't pour into the centre hole, that's the airflow chimney. Putting liquid there will cause it to leak straight out the bottom.

Step 4: Seal It Back Up

Once you've filled the pod, close it immediately.

• For top-fill XROS pods: Snap the mouthpiece firmly back on. You should hear a click that tells you it's secure.
• For side-fill pods: Push the silicone plug back firmly into place. Make sure it sits flush with the pod surface so it creates a good seal.

Step 5: The Important Wait – Priming the Coil

This is the step that many users overlook, and which is the cause of the burned taste. It is important to ensure that you wait until the e-liquid gets absorbed by the coil.

The pod should be left to rest for a minimum of 5-10 minutes. This allows the cotton wick to fully absorb the liquid. If you vape immediately, you'll burn the dry cotton. Once burnt, the coil is ruined permanently. Hold the pod upright while filling to reduce the chance of air bubbles and leaks. 

Step 6: Reattach and Vape

After waiting, put the pod back into the battery if you removed it. Turn your vape back on (click five times) and you're ready to go.

Common Refill Problems Explained

Even if you follow the steps, you might sometimes face issues. Here's how to fix the most common ones.

Problem: Burnt taste after refilling.

Solution:

Most probably you have not waited long enough for your coil to prime. In case the taste remains burnt even after waiting, it is a damaged coil. You need to replace the pod.

Problem: E-liquid leaking from the pod.

Solutions:

• Overfilling: You filled it too much. Next time, leave the air gap.
• Wrong hole: You may have poured liquid into the centre airflow tube. This will cause leaks every time.
• Loose seal: For side-fill pods, the silicone plug wasn't closed properly. For XROS pods, the mouthpiece wasn't clicked on securely.

Problem: Gurgling sound when you vape.

Solution:

There's excess liquid in the coil or airflow. Remove the pod and place a tissue on the air vent. Blow through the mouthpiece to remove any extra liquid.

Problem: No Vapour After Refilling

Solution:

• Check that the pod is fully inserted.
• Make sure the battery has charge.
• Confirm the pod makes proper contact with the device.
• If the pod is old or damaged, replace it.

This is one of the most common issues after refilling.

Which E-Liquid Should You Use?

Using the right e-liquid helps prevent leaks and improves performance.

50/50 or 60/40 VG/PG: This is the best ratio for pod systems like the XROS. The liquid is thin enough to wick properly but thick enough to not leak.

70/30 VG/PG or higher: This thick liquid is for sub-ohm tanks, not small pods. Using it in a pod will cause burnt hits because the coil can't absorb it fast enough.

When to Replace Your Vaporesso Pod

A pod doesn't last forever, you'll know it's time for a new one when:

• The flavour becomes weak or muted
• You get a consistent burnt taste, even after proper priming
• Vapour production drops significantly
• It starts leaking from the bottom, and you've already checked for the common causes

Most Vaporesso pods last around one to two weeks, although lifespan varies depending on usage habits, e-liquid type, and coil resistance. 

Conclusion

Refilling your Vaporesso pod is straightforward when you follow the right steps. Start by identifying your pod type - top-fill for XROS or side-fill for Luxe series. Always turn off your vape, open the correct fill port, and pour slowly while leaving a small air gap. 

Never put liquid in the centre airflow hole. After filling, seal the pod properly and wait at least five minutes for the coil to prime. This waiting step prevents burnt hits and extends pod life. Also, use 50/50 VG/PG e-liquids for best performance. 

If you face leaks or gurgling, check for overfilling, loose seals, or excess liquid in the airflow. With practice, refilling becomes quick. By following these simple steps and using the right e-liquid for your Vaporesso pod, you can reduce leaks, prevent burnt hits, and enjoy consistent flavour throughout the life of your pod.